logo

Crowdly

Browser

Додати до Chrome

ECNG1012 : Engineering Science and Technology (Semester I- 2024/2025)

Шукаєте відповіді та рішення тестів для ECNG1012 : Engineering Science and Technology (Semester I- 2024/2025)? Перегляньте нашу велику колекцію перевірених відповідей для ECNG1012 : Engineering Science and Technology (Semester I- 2024/2025) в myelearning.sta.uwi.edu.

Отримайте миттєвий доступ до точних відповідей та детальних пояснень для питань вашого курсу. Наша платформа, створена спільнотою, допомагає студентам досягати успіху!

When the TRIGGER COUPLING switch is set to AUTO and free runs are displayed on the oscilloscope screen, which of the following is implied?

Переглянути це питання
X-Y operating mode is used to plot the Channel 2 signal on the Y axis and the Channel 1 signal on  the X axis. This mode is independent of the time and plots CH2 voltage with respect to CH1 voltage. To activate X-Y mode on the 2121 oscilloscope, which three actions must be performed?

i. Switch 27 must be set to its X-Y position.ii. Switch 10 must be set to its X-Y position.iii. Switch 18 must be set to its X-Y position.iv. Switch 11 must be set to its X-Y position.v. Button 30 must be depressed /down. oscilloscope

Переглянути це питання
Which switch on the 2121 oscilloscope is used to set the triggering source to Channel 1, Channel 2 or to an external source etc.? 

oscilloscope

0%
0%
0%
0%
Переглянути це питання
Which knob on the 2121 oscilloscope can be used to adjust the time base?

  oscilloscope

Переглянути це питання
To output signal from the function generator for general use, the leads must be connected to: 

function generator

0%
0%
0%
0%
Переглянути це питання
The oscilloscope settings for waveform shown below are as follows:

  • the CH1 VOLTS/DIV setting is 2 VOLTS/DIV,
  • the CH2 VOLTS/DIV setting is 0.5 VOLTS/DIV and
  • the TIME/DIV setting is 0.2 ms/DIV.

Note: each square on the oscilloscope grid / articulate has a height of 1 DIV and a width of 1 DIV.

Given that it is the Channel 2 waveform being displayed, what is the peak to peak voltage of the waveform in Volts (pk-pk)

Do not include the units i.e. Volts (pk-pk) in your answer as it will be marked as incorrect by the software. Enter the value only.

square wave
Переглянути це питання
To output the smallest possible signals from the function generator, button 11 must be depressed or in the down position. When this button is depressed, the signal is attenuated by -20 dB or to 1/10 of the amplitude. 

function generator

0%
0%
Переглянути це питання
Why should the vernier adjustment calibration knobs on the oscilloscope be set to their CAL'D positions?
0%
0%
0%
0%
Переглянути це питання
What action must be executed to extend the Sec/Div switch setting by a factor of 10 on the  2160A oscilloscope? 

2160A oscilloscope

0%
0%
0%
0%
Переглянути це питання
To set the frequency to 1KHz, the frequency range button group labelled 2 can be set to:i. 500ii. 5kiii. 50kiv. 50v. 500kbefore setting the coarse and fine frequency controls. function generator
0%
0%
0%
Переглянути це питання

Хочете миттєвий доступ до всіх перевірених відповідей на myelearning.sta.uwi.edu?

Отримайте необмежений доступ до відповідей на екзаменаційні питання - встановіть розширення Crowdly зараз!

Browser

Додати до Chrome