logo

Crowdly

Browser

Додати до Chrome

Materials Science A / Materiaalkunde A - 214

Шукаєте відповіді та рішення тестів для Materials Science A / Materiaalkunde A - 214? Перегляньте нашу велику колекцію перевірених відповідей для Materials Science A / Materiaalkunde A - 214 в stemlearn.sun.ac.za.

Отримайте миттєвий доступ до точних відповідей та детальних пояснень для питань вашого курсу. Наша платформа, створена спільнотою, допомагає студентам досягати успіху!

A tensile specimen with an original 10 mm diameter carries a load of 5840 N. Calculate its diameter under this load. Give your answer to 4 significant digits.

Assume: E = 209 GPa and ν = 0.35

'n Trek monster met 'n oorpronklike diameter van 10 mm dra 'n las van 5840 N. Bereken die diameter onder die las. Gee jou antwoord tot 4 beduidende syfers.

Neem aan E = 209 GPa en ν = 0.35

Переглянути це питання

The following equations are only valid up until the following point on a stress-strain curve.

sigma equals E epsilon
epsilon subscript l a t e r a l end subscript equals negative nu epsilon subscript a x i a l end subscript

Die vergelykings wat volg is slegs geldig tot die volgende punt op die spanning-spanning kurwe.

sigma equals E epsilon
epsilon subscript l a t e r a a l end subscript equals negative nu epsilon subscript a k s i a a l end subscript

Переглянути це питання

A linear elastic relationship, as described by Hooke's Law, is only applicable to normal stress and strain.

'n Lineêre elastiese verhouding, soos beskryf deur Hooke se Wet, is slegs van toepassing op normale spanning en vervorming.

0%
0%
Переглянути це питання

Multiple answers may apply here. Please select the correct terms. / Verskeie antwoorde kan hier van toepassing wees. Kies asb die regte terme.

A linear elastic materials shows a directly proportional relationship between

'n Lineêre elastiese materiaal toon 'n direk eweredige verhouding tussen

0%
0%
0%
Переглянути це питання

Plastic deformation is related to slip due to shear stress along densely packed atomic planes; interatomic bonds are broken and atoms bond with a new set of nearest neighbours during plastic deformation.

Plastiese deformasie is verwant aan die glip wat veroorsaak is deur die skuifspanning langs die dig verpakte atomiese vlakke; interatomiese bindings word verbreek en atome bind met 'n nuwe stel naaste bure tydens plastiese vervorming.

 

0%
0%
Переглянути це питання

Elastic deformation occurs when an applied load is sufficiently large enough to move atoms from their equilibrium spacing position in the crystal lattice without breaking any interatomic bonds.

Elastiese deformasie vind plaas as 'n aangewende las groot genoeg is om atome van hulle ekwilibriumspaseringposisie in die kristalrooster te beweeg, sonder om enige interatomiese bindings te breek.

0%
0%
Переглянути це питання

While impurity atoms that are smaller than the host metal atom reduce the strength of the metal alloy, larger impurity atoms increase the lattice strain energy thereby increasing the strength of the metal alloy.

0%
100%
Переглянути це питання

A steel rod is drawn from 10 mm to 7 mm diameter. It is then put through a recovery heat treatment during which the rod returns to its original diameter.

0%
0%
Переглянути це питання

The approximate melting temperature of aluminium is 660 °C. The corresponding recrystallisation temperature for aluminium that has been cold-worked at least 5% is 80 °C. This correlates to the following relationship:

50%
50%
0%
Переглянути це питання

 Choose the correct term for each description.

Kies die regte term vir elke beskrywing.

 

Переглянути це питання

Хочете миттєвий доступ до всіх перевірених відповідей на stemlearn.sun.ac.za?

Отримайте необмежений доступ до відповідей на екзаменаційні питання - встановіть розширення Crowdly зараз!

Browser

Додати до Chrome